info@workshop-manual-pdf.com
Workshop Manual

John Deere PowerTech 4.5L & 6.8L Base Engine Technical Manual CTM104 PDF

John Deere PowerTech 4.5L & 6.8L Base Engine Technical Manual CTM104 PDF
Official Technical Service Publication

John Deere PowerTech 4.5L & 6.8L Base Engine Technical Manual CTM104 PDF

Complete factory service manual, fastener tightening torques, fault diagnostic trees, and mechanical/electrical specifications. Published under our single authoritative standard as a 100% free ($0.00) clean PDF download without paywalls, forms, or checkout.

Displacement
4.5L (4045) & 6.8L (6068)
4-Cyl & 6-Cyl Diesel
Cylinder Head Torque
75 + 110 lb-ft + 90°
Torque-to-Yield Pattern
Cold Valve Lash
In 0.014 / Ex 0.018 in
In 0.36 / Ex 0.46 mm
Engine Oil Capacity
4045: 14 Qts | 6068: 20 Qts
13.2 L / 18.9 L
ADVERTISEMENT

John Deere PowerTech 4045 & 6068 Base Engine Component Specifications & Fastener Torques

The following engineering data is verified from factory documentation for certified technicians and equipment operators:

Engineering SpecificationFactory Service Value / Tolerance
Engine FamiliesJohn Deere 4.5L (4045) and 6.8L (6068) PowerTech & PowerTech Plus Engines
Configuration4-Cylinder (4045) and 6-Cylinder (6068) In-Line 4-Cycle Diesel
Bore x Stroke106.0 mm x 127.0 mm (4.17 in x 5.00 in)
Displacement4045: 4.5 Liters (276 cu in) | 6068: 6.8 Liters (414 cu in)
Compression Ratio17.0:1 (Turbocharged / Air-to-Air Aftercooled)
Firing Order4045: 1 – 3 – 4 – 2 | 6068: 1 – 5 – 3 – 6 – 2 – 4
Cylinder Head Cap ScrewsStep 1: 100 Nm (75 lb-ft), Step 2: 150 Nm (110 lb-ft), Step 3: Advance each screw 90 degrees (Torque-to-Yield)
Main Bearing Cap Screws135 Nm (100 lb-ft) + 90 degrees
Connecting Rod Cap Screws70 Nm (52 lb-ft) + 90 degrees
Flywheel Retaining Screws140 Nm (103 lb-ft)
Intake Valve Lash (Cold)0.36 mm (0.014 inch)
Exhaust Valve Lash (Cold)0.46 mm (0.018 inch)
Cylinder Liner Protrusion0.030 to 0.100 mm (0.001 to 0.004 inch) above block deck
ADVERTISEMENT

Complete Service Chapter Breakdown & System Scope

  • Section 01: General Information, Engine Serial Plates, Fastener Torque Safety & Identification
  • Section 02: Engine Cylinder Head, Multi-Angle Valve Seats, Guides & Camshaft Bushings
  • Section 03: Cylinder Block, Directed Liner O-Rings, Liner Flange Protrusion & Main Journals
  • Section 04: Crankshaft, Connecting Rods, Piston Ring Gap Orientation & Oil Spray Nozzles
  • Section 05: Camshaft, Front Timing Gear Train Alignment & Balancer Shafts (4-Cylinder 4045)
  • Section 06: Lubrication System: Engine Oil Pump, Pressure Relief Valve & Oil Cooler Core
  • Section 07: Cooling System: Heavy-Duty Water Pump, Thermostat & Coolant Flow Schematics
  • Section 08: Special Service Tools, Dial Indicators, Liner Pullers & Assembly Fixtures

🛠️ Commercial Heavy Equipment Engineering Calculators

Calculate bolt torques, hydraulic cylinder push/pull tonnage, compression ratios, and 3-phase alternator vectors online.

Open Engineering Suite →

Frequently Asked Questions (FAQ)

Q: Can John Deere cylinder head bolts be reused on PowerTech 4045 and 6068 engines?
A: No, John Deere specifies torque-to-yield cylinder head bolts. Always install brand new OEM head bolts because they permanently stretch during the final 90-degree angle turn.

Q: What is the liner protrusion specification for JD 4045 and 6068 engines?
A: Wet cylinder liner protrusion must measure between 0.030 and 0.100 mm (0.001 to 0.004 in) above the top deck surface. Shims are available if protrusion is below specification.

Q: How do you orient the balancer shafts on the 4-cylinder 4045 engine?
A: Align the timing punch marks on the crankshaft gear with the drive gears on both the left and right balancer shafts to eliminate secondary engine vibration.

Leave a Reply

Your email address will not be published. Required fields are marked *