info@workshop-manual-pdf.com
Workshop Manual

Kubota B2301 & B2601 Compact Tractor Workshop Service Manual PDF

Kubota B2301 & B2601 Compact Tractor Workshop Service Manual PDF
Official Technical Service Publication

Kubota B2301 & B2601 Compact Tractor Workshop Service Manual PDF

Complete factory service manual, fastener tightening torques, fault diagnostic trees, and mechanical/electrical specifications. Published under our single authoritative standard as a 100% free ($0.00) clean PDF download without paywalls, forms, or checkout.

Displacement
D1005 / D1105 Diesel
1.001L / 1.123L 3-Cyl
Cylinder Head Torque
43.4–47.0 lb-ft
58.8–63.7 Nm
Cold Valve Lash
0.0057–0.0073 in
0.145–0.185 mm
Engine Oil Capacity
3.3 Quarts
3.1 Liters
ADVERTISEMENT

Kubota B2301 & B2601 Compact Tractor & Diesel Engine Specifications

The following engineering data is verified from factory documentation for certified technicians and equipment operators:

Engineering SpecificationFactory Service Value / Tolerance
Engine ModelsKubota D1005-E4-D27 (B2301) / D1105-E4-D27 (B2601) Tier 4
Engine Type3-Cylinder, In-line, 4-Cycle Liquid-Cooled Diesel
Total DisplacementB2301: 1.001 Liters (61.1 cu in) | B2601: 1.123 Liters (68.5 cu in)
Gross HorsepowerB2301: 22.0 HP @ 2800 RPM | B2601: 25.5 HP @ 2800 RPM
Transmission TypeHST (Hydrostatic Transmission – 3 Range Forward / Reverse)
Cylinder Head Bolt Torque58.8 to 63.7 Nm (43.4 to 47.0 lb-ft) in progressive sequence
Main Bearing Case Bolt Torque29.4 to 34.3 Nm (21.7 to 25.3 lb-ft)
Connecting Rod Bolt Torque26.5 to 30.4 Nm (19.5 to 22.4 lb-ft)
Cold Valve Clearance (In/Ex)0.145 to 0.185 mm (0.0057 to 0.0073 inch)
Fuel Injection PumpBosch MD type mini pump (Injection Timing: 16.0° to 17.5° BTDC)
Hydraulic System Relief Pressure13.7 to 14.2 MPa (140 to 145 kgf/cm2 / 1991 to 2062 psi)
Transmission / Hydraulic Fluid Capacity15.0 Liters (4.0 US Gallons) Kubota Super UDT-2
ADVERTISEMENT

Complete Service Chapter Breakdown & System Scope

  • Section 1: Tractor Identification, Safety Labels, Work Precautions & Special Tools
  • Section 2: Engine Body Overhaul: Cylinder Head, Valves, Pistons, Crankshaft & Oil Clearance
  • Section 3: Fuel System: Bosch Injection Pump, Governor Springs & Injector Nozzle Testing
  • Section 4: Hydrostatic Transmission (HST): Variable Displacement Swashplate Pump & Motor
  • Section 5: Rear Axle, Differential Lock, Wet Disc Brakes & Final Reduction Gears
  • Section 6: Front Axle Drive (4WD): Bevel Gear Case, King Pin Bushings & Steering Knuckles
  • Section 7: Hydraulic System: Gear Pump, 3-Point Hitch Control Valve & Hydraulic Cylinder
  • Section 8: Electrical System: OPC Safety Switches, Dynamo Charging, Starter & Color Schematics

🛠️ Commercial Heavy Equipment Engineering Calculators

Calculate bolt torques, hydraulic cylinder push/pull tonnage, compression ratios, and 3-phase alternator vectors online.

Open Engineering Suite →

Frequently Asked Questions (FAQ)

Q: What transmission fluid is required for Kubota B2301 and B2601 tractors?
A: Use only genuine Kubota Super UDT-2 synthetic multi-purpose transmission hydraulic fluid to prevent HST whine, friction disc chatter, and cavitation.

Q: What is the engine oil capacity and weight for the B2601?
A: The engine oil capacity is 3.1 Liters (3.3 US Quarts) with filter. Recommended oil is API CJ-4 or CK-4 10W-30 or 15W-40.

Q: How do I check hydraulic relief pressure on Kubota B-Series tractors?
A: Connect a 0–3,000 PSI pressure gauge to the hydraulic quick coupler, run engine at rated 2800 RPM, and actuate the valve. Relief pressure should register between 1991 and 2062 PSI.

Leave a Reply

Your email address will not be published. Required fields are marked *