info@workshop-manual-pdf.com
Workshop Manual

Yanmar 3JH3E & 4JH3E Marine Diesel Engine Service Manual PDF

Yanmar 3JH3E & 4JH3E Marine Diesel Engine Service Manual PDF
Official Technical Service Publication

Yanmar 3JH3E & 4JH3E Marine Diesel Engine Service Manual PDF

Complete factory service manual, fastener tightening torques, fault diagnostic trees, and mechanical/electrical specifications. Published under our single authoritative standard as a 100% free ($0.00) clean PDF download without paywalls, forms, or checkout.

Displacement
3JH3E (1.38L) | 4JH3E (1.82L)
3-Cyl & 4-Cyl Marine
Cylinder Head Torque
54.2–57.8 lb-ft
73.5–78.5 Nm
Cold Valve Lash
0.008 in (0.20 mm)
Intake & Exhaust
Engine Oil Capacity
3JH3E: 5.3 Qt | 4JH3E: 6.3 Qt
5.0 L / 6.0 L
ADVERTISEMENT

Yanmar 3JH3E & 4JH3E Marine Diesel Engine Tightening Torques & Technical Specifications

The following engineering data is verified from factory documentation for certified technicians and equipment operators:

Engineering SpecificationFactory Service Value / Tolerance
Engine ModelsYanmar 3JH3E (3-Cylinder) and 4JH3E (4-Cylinder) Marine Diesel Engines
Combustion SystemDirect Injection (DI), 4-Cycle Liquid-Cooled Marine Inboard
Total Displacement3JH3E: 1.380 Liters (84.2 cu in) | 4JH3E: 1.824 Liters (111.3 cu in)
Continuous Power Rating3JH3E: 36.5 HP @ 3700 RPM | 4JH3E: 50.0 HP @ 3700 RPM
Bore x Stroke84.0 mm x 82.0 mm (3.31 in x 3.23 in)
Firing Order3JH3E: 1 – 2 – 3 | 4JH3E: 1 – 3 – 4 – 2
Cylinder Head Bolts Torque73.5 to 78.5 Nm (54.2 to 57.8 lb-ft) applied in progressive center-out sequence
Main Bearing Bolts Torque73.5 to 78.5 Nm (54.2 to 57.8 lb-ft)
Connecting Rod Bolts Torque44.1 to 49.0 Nm (32.5 to 36.1 lb-ft)
Flywheel Bolts Torque83.3 to 88.2 Nm (61.4 to 65.0 lb-ft)
Cold Valve Clearance (In/Ex)0.20 mm (0.008 inch)
Fuel Injection Opening Pressure19.6 to 20.6 MPa (200 to 210 kgf/cm2 / 2844 to 2986 psi)
Marine Gearbox CompatibilityYanmar KM35A / KM35P / KM4A / Saildrive SD40
ADVERTISEMENT

Complete Service Chapter Breakdown & System Scope

  • Section 1: General Marine Engine Data, Serial Plate Locations & Safety Precautions
  • Section 2: Engine Body Inspection: Cylinder Head, Valve Guides, Camshaft & Piston Clearances
  • Section 3: Marine Raw-Water & Fresh-Water Cooling: Heat Exchanger, Neoprene Impeller & Thermostat
  • Section 4: Fuel Injection System: Bosch MP-Pump, Mechanical Governor & Multi-Hole Nozzles
  • Section 5: Lubrication System: Trochoid Oil Pump, Pressure Regulating Valve & Full-Flow Filter
  • Section 6: Electrical & Starting System: 12V High-Output Marine Alternator, Starter Motor & Instrument Panel
  • Section 7: Marine Transmission & Reduction Gear (KM-Series): Wet Multiple Disc Clutch & Reverse Gears
  • Section 8: Winterization, Seawater Drain Plugs, Sacrificial Zinc Anodes & Lay-Up Storage

🛠️ Commercial Heavy Equipment Engineering Calculators

Calculate bolt torques, hydraulic cylinder push/pull tonnage, compression ratios, and 3-phase alternator vectors online.

Open Engineering Suite →

Frequently Asked Questions (FAQ)

Q: How often should the seawater pump impeller and sacrificial anodes be replaced on Yanmar JH3 engines?
A: Inspect the flexible rubber seawater pump impeller every 250 operating hours or annually. Inspect zinc anodes in the heat exchanger and cylinder block every 6 months and replace when eroded beyond 50%.

Q: What engine oil viscosity is recommended for Yanmar marine diesels?
A: Use API CD, CF, or CI-4 SAE 15W-40 marine diesel oil. Never use automotive oils with low friction modifiers in marine inboard engines.

Q: What is the valve lash clearance for Yanmar 3JH3E and 4JH3E?
A: Both intake and exhaust valve clearances must be adjusted to 0.20 mm (0.008 inch) when cold at Top Dead Center (TDC) of the compression stroke.

Leave a Reply

Your email address will not be published. Required fields are marked *