Description
(adsbygoogle = window.adsbygoogle || []).push({});
This official Perkins 2800 Series (2806C-E18TA, 2806D-E18TA, 2806F, 2806J) 18.1L Heavy Diesel Maintenance & Workshop Manual provides complete factory overhaul specifications, MEUI electronic unit injector calibration, and M18 multi-stage torque-angle tightening sequences for heavy industrial machinery and multi-megawatt standby generator sets.
⚙️ Perkins 2806 (18.1L) Heavy Duty Engine Architecture
| Specification Parameter | Perkins 2806C-E18TA / 2806D-E18TA Specification |
|---|---|
| Cylinder Configuration | 6-Cylinder In-Line, 4-Stroke Industrial Diesel |
| Bore & Stroke | 145.0 mm x 183.0 mm (5.71 in x 7.20 in) |
| Total Displacement | 18.1 Litres (1,104.5 cu in) |
| Aspiration System | Turbocharged with Air-to-Air Charge Air Cooling (ATAAC) |
| Combustion System | Direct Injection Mechanically Actuated Electronic Unit Injector (MEUI) |
| Firing Order | 1 – 5 – 3 – 6 – 2 – 4 (Cylinder 1 at front gear housing) |
| Compression Ratio | 14.5:1 |
| Cold Valve Lash Clearance | Inlet: 0.38 mm (0.015 in) | Exhaust: 0.76 mm (0.030 in) |
| MEUI Unit Injector Height Setting | 78.0 ± 0.2 mm (using timing gauge block) |
| Lube Oil Sump Capacity | 62.0 Litres (16.4 US Gal) |
| Power Output Range | 429 – 597 kW (575 – 800 bhp) @ 1800 – 2100 RPM |
🔧 Perkins 2800 Multi-Stage Fastener Torque-Angle Tightening Protocol
Clean all fastener threads and lightly coat with clean 15W-40 engine oil. Follow the manufacturer torque-angle sequence:
| Fastener Component | Size / Grade | Stage 1 Preload | Final Tightening Angle |
|---|---|---|---|
| Cylinder Head Studs / Bolts | M18 High-Tensile | 160 N·m (118 lbf·ft) → Re-torque 160 N·m | Tighten +120° Angle |
| Connecting Rod Big End Bolts | Fractured Joint Cap | 90 N·m (66 lbf·ft) | Tighten +90° Angle |
| Main Bearing Cap Bolts | M20 High-Tensile | 150 N·m (111 lbf·ft) | Tighten +90° Angle |
| Crankshaft Front Vibration Damper | M16 | 115 N·m (85 lbf·ft) | Tighten +90° Angle |
| Flywheel Mounting Bolts | M16 | 135 N·m (100 lbf·ft) | Tighten +60° Angle |
| Rocker Arm Shaft Pedestal Bolts | M12 | — | 109 N·m (80 lbf·ft) |
| MEUI Unit Injector Hold-Down Bolt | M10 | — | 55 N·m (41 lbf·ft) |
🛠️ Fastener Torque & Generator Power Calculators
Overhauling a high-horsepower generator set or calculating engine thermal loading? Use our free workshop suite for instant bolt torque conversion (Nm to lb-ft) and generator fuel consumption:
📑 Workshop Overhaul Sections Included
- General Information & Technical Specifications – Engine model codes (JG, HGA, HGB), lifting bracket safety, and service tooling part numbers.
- Cylinder Block & Rotating Assembly – Crankshaft journal regrinding limits, main bearing oil clearances, fractured connecting rod inspection, and cylinder liner cross-hatch honing.
- Cylinder Head & Valvetrain – Crosshead bridge adjustment, valve guide wear limits, dual valve spring testing, and cold valve lash clearances.
- MEUI Fuel Injection & Electronic Engine Management – Electronic Control Module (ECM) sensor inputs (coolant temperature, boost pressure, engine speed/timing), injector solenoid testing, and fuel transfer pump priming.
- Lubrication & Cooling Circuits – Heavy-duty engine oil cooler core pressure testing, dual thermostat opening temperatures (82°C – 93°C), and gear-driven water pump impeller replacement.








Reviews
There are no reviews yet.