Description
(adsbygoogle = window.adsbygoogle || []).push({});
Perkins 1104D 44T / 44TA Fastener & Service Standards
4.4 Liters (4-Cyl)
Stage 1: 110 Nm + 150°
In: 0.20mm / Ex: 0.45mm
8.4 Liters 15W-40
This official Perkins 1104D-E44T & 1104D-E44TA Electronic Industrial Engine Maintenance & Workshop Manual provides complete factory overhaul procedures, ECM wiring schematics, common rail fuel injection troubleshooting, and torque-angle specifications for Perkins 1104D electronic engines (Build Codes NR and NS). Developed for commercial technicians working with Tier 3 / Stage IIIA compliant industrial, agricultural, and power generation equipment.
⚡ Perkins 1104D Electronic (E44T & E44TA) Engine Architecture
| Engine Parameter | Perkins 1104D-E44T (NR Build) | Perkins 1104D-E44TA (NS Build) |
|---|---|---|
| Configuration | 4-Cylinder In-Line, 4-Stroke Electronic Diesel | 4-Cylinder In-Line, 4-Stroke Electronic Diesel |
| Bore & Stroke | 105.0 mm x 127.0 mm (4.13 in x 5.00 in) | 105.0 mm x 127.0 mm (4.13 in x 5.00 in) |
| Total Displacement | 4.4 Litres (269 cu in) | 4.4 Litres (269 cu in) |
| Aspiration | Turbocharged with Wastegate | Turbocharged & Air-to-Air Charge Cooled (ATAAC) |
| Fuel Delivery System | Electronic Common Rail (HPCR) up to 1,600 bar | Electronic Common Rail (HPCR) up to 1,600 bar |
| Electronic Engine Management | Perkins ECM (A4E2 Controller), SAE J1939 CAN | Perkins ECM (A4E2 Controller), SAE J1939 CAN |
| Firing Order | 1 – 3 – 4 – 2 (Cylinder 1 at front) | 1 – 3 – 4 – 2 (Cylinder 1 at front) |
| Compression Ratio | 16.2:1 | 16.2:1 |
| Inlet Valve Lash (Cold) | 0.20 mm (0.008 in) | 0.20 mm (0.008 in) |
| Exhaust Valve Lash (Cold) | 0.45 mm (0.018 in) | 0.45 mm (0.018 in) |
| Lube Oil Sump Capacity | 8.0 – 8.5 Litres (8.5 – 9.0 US qts) | 8.0 – 8.5 Litres (8.5 – 9.0 US qts) |
🔧 Critical Bolt Torque Tightening Protocols
Ensure fastener threads are clean and lubricated with engine oil. Tighten following the manufacturer spiral sequence:
| Fastener Component | Size / Grade | Initial Torque | Final Torque / Angle |
|---|---|---|---|
| Cylinder Head Short Bolts (S) | M14 High-Tensile | 50 Nm → 100 Nm | +150° Angle |
| Cylinder Head Medium Bolts (M) | M14 High-Tensile | 50 Nm → 100 Nm | +180° Angle |
| Cylinder Head Long Bolts (L) | M14 High-Tensile | 50 Nm → 100 Nm | +210° Angle |
| Connecting Rod Cap Bolts | Fractured Joint Cap | 50 Nm (37 lbf-ft) | +90° Angle |
| Main Bearing Cap Bolts | M16 | 110 Nm (81 lbf-ft) | +90° Angle |
| Crankshaft Pulley Center Bolt | M16 | 115 Nm (85 lbf-ft) | +180° Angle |
| High Pressure Fuel Rail Mounting | M8 | — | 22 Nm (16 lbf-ft) |
| Common Rail Electronic Injector Clamp | M8 | — | 33 Nm (24 lbf-ft) |
| High Pressure Pipe Union Nuts | M14 | — | 30 Nm (22 lbf-ft) |
🛠️ Fastener Torque & Diesel Engineering Calculators
Need to convert torque units or verify fastener tension under heat expansion? Use our free workshop suite for instant bolt torque conversions, generator fuel consumption, and displacement calculations:
💻 Common Rail Electronic Diagnostics & ECM Architecture
The Perkins 1104D Electronic series utilizes advanced Electronic Engine Management capable of continuous self-diagnosis and J1939 telemetry broadcast:
- A4E2 Engine Control Module (ECM) – 70-pin / 120-pin harness connectors, dual microprocessor architecture, and flash memory calibration.
- Crankshaft & Camshaft Speed/Timing Sensors – Hall effect and inductive sensors reading 60-2 tooth trigger wheels on the crankshaft and single-tooth camshaft indicators.
- High Pressure Common Rail (HPCR) – Rail pressure sensor (RPS) output voltage diagnostics (0.5V at 0 bar to 4.5V at 1,600 bar) and high-pressure limiter valve relief operation.
- CANbus Diagnostic Troubleshooting – Fault code interpretation for SPN 100 (Engine Oil Pressure), SPN 110 (Coolant Temperature), SPN 157 (Fuel Rail Pressure), and SPN 190 (Engine Speed).








Reviews
There are no reviews yet.