info@workshop-manual-pdf.com
Workshop Manual

Perkins 2500 Series 2506F 2506J-E15TA Engine Workshop Manual

0 Stationery Engines

Perkins 2500 Series 2506F 2506J-E15TA Engine Workshop Manual

Factory Workshop Reference • 100% Free ($0.00)

Perkins 2500 Series (2506F & 2506J-E15TA) Diesel Engine

DISPLACEMENT
15.2L (928 cu in)

CYLINDER HEAD TORQUE
See Factory Angle Tightening Procedure

COLD VALVE LASH
Inlet 0.38 mm / Exhaust 0.76 mm

OIL CAPACITY
62.0 Liters (16.4 US Gal)

• Unbundled Adobe PDF • No checkout or registration • Clean OEM Document

Advertisement

The Perkins 2500 Series (2506F-E15TA / 2506J-E15TA) is an advanced heavy-duty 15.2-liter inline 6-cylinder diesel engine engineered for high-performance generator sets (up to 550 kVA) and severe-duty industrial plant equipment. This official workshop manual details electronic fuel injection calibrations, valve and Jake brake adjustments, emissions maintenance, and complete workshop repair standards.

🔧 Need Real-Time Technical Calculators?

Convert fastener torque (Nm ↔ ft-lb), calculate cylinder displacement, or check turbo boost pressure ratio.

🔧 Complete Technical Specifications & Torque Sequences

Reference the OEM factory tightening torques, clearances, and operational parameters for Perkins 2500 Series (2506F & 2506J-E15TA) Diesel Engine below:

Engine PlatformPerkins 2506F-E15TA & 2506J-E15TA Industrial
Configuration6 Cylinders Inline, 4-Stroke Diesel
Cylinder Bore137 mm (5.39 in)
Piston Stroke171 mm (6.73 in)
Total Displacement15.2 Liters (928 Cubic Inches)
AspirationTurbocharged with Air-to-Air Charge Cooler (ATAAC)
Compression Ratio16.0:1
Governor TypeElectronic Control Module (A4E4 / ECM Controlled)
Intake Valve Lash (Cold)0.38 mm ± 0.08 mm (0.015 in ± 0.003 in)
Exhaust Valve Lash (Cold)0.76 mm ± 0.08 mm (0.030 in ± 0.003 in)
Unit Injector Preload Dimension78.0 mm ± 0.2 mm (Height setting tool)
Engine Oil Pan Sump CapacityMinimum 48.0 Liters / Maximum 62.0 Liters
Cooling System CapacityEngine Only: 25.8 Liters (6.8 US Gal)
Firing Order1 – 5 – 3 – 6 – 2 – 4
Maximum Idle Speed1,800 to 2,100 RPM (Application Specific)

Advertisement

📖 Workshop Service Manual Table of Contents

This unbundled factory manual covers full overhaul, diagnostic procedures, and disassembly protocols:

  1. General Safety Instructions & Hazardous Material Precautions
  2. Engine Identification Numbers, Nameplate Locations & Core Specifications
  3. Daily Inspection Protocol & Fluid Level Verifications
  4. Maintenance Interval Schedules (Every 500, 1000, 2000 & 3000 Operating Hours)
  5. Cylinder Head Inspection, Valve Clearance & Jake Brake Setting Protocols
  6. Electronic Unit Injector (MEUI-C) Installation, Adjustment & Calibration
  7. Fuel System: Primary/Secondary Filter Changes & Fuel Water Separator Draining
  8. Lubrication System: Heavy Duty Engine Oil (Perkins Powerpart) & Cartridge Servicing
  9. Turbocharger & Aftercooler Inspection: Radial/Axial Play Limits
  10. Electronic Diagnostic Codes: Active vs Logged Faults, Sensor Voltage Matrix

Ready to start your overhaul or inspection?

Instant clean PDF download. Save to your phone, tablet, or shop laptop for field use.


📥 Download Free Perkins 2500 Series 2506F 2506J-E15TA Engine Workshop Manual (.PDF)

Explore more factory documentation in our Perkins Manuals Archive or explore our interactive Diagnostic Engineering Calculators.

About The Author

Leave a Reply

Your email address will not be published. Required fields are marked *

Privacy Policy